Hello. I had severe leaks with mine. With fresh wick be sure the cotton is not touching the airflow holes because it is going do drip. Put some juice on it because it is easier to shape it then use your pinchers to lift it away. Do not leave the juice holes open when you fill the tank. The pressure created in the tank when you screw the cap is going to push the ejuice and owerflow the deck. With fresh wick after the tank is filled and the cap is screwed open the juice flow fo 1 or 2 seconds then close it. Take 2-3 puffs then open it again and you should see air bubbles. Close it again and take another few puffs. The goal is to gradualy release the presure created in the tank when screwing the cap. Do this also when refilling. For me works. I have filled my pockets with juice many times until i realized its dripping because the cotton was touching the side airflow holes. I hope this will work for you too. I am from Romania so not a native english speaker but hopefully you will understand what i mean. Have a nice vape
Great video Mike- just got 2 shipped over (1 silver, 1 black) did a build on the black with dual coil set-up as directed and it's vaping so sweet straight off the bat. Just came over from the Smok Cloudbeast V8 where I have been rebuilding on their supplied deck. The pillars used to pull inwards and then the seal between the 2 connecters would melt and that was end of deck! Got recommended to buy the Ammit Dual RTA and basically couldn't be happier. Thanks for walking me through the build- spot on directions:)
bought one back in September and the included a top fill adapter and a piece to separate the air flow down in the base more like the kylin to smooth out the whistling sound just remember if you use the top fill adapter you need to add an oring or it will leak
Mine was leaking above the air flow adjustment, put one of the bigger clear o-rings around the build deck just above the treads to mount the tank, no more leaks just made a small gap between the tank and the base!! I like that gap more then the greasy fingers :p
1st step: Unscrew the pin underneath and remove everything including the air hole, theres also a lil brown cap that remove that to,
Step2: once you have dissembled step 1, reassemble it and tighten the pin as hard as you can of course you will no when to stop cause you will feel like you have tighting that bitch.
This is the reason why it leaks from the airhole an from underneath your tank when you remove it from your mod. You will see leaks.
Now that is solved least but final.
Step 3: put an o ring on both caps. The filling cap and the top closing cap. So therefore both top caps requires an o ring.
Now fucking wick that shit just dont cover the air holes.
An do your self a favour use a single coil is much better.
i just don’t understand why everybody is ignoring the metal piece with the two openings.. this piece is found in the lower layer of the packaging and it is meant to keep the glass in its place and not to pop up when opining the top part of the rta … put this part above the glass screw it and then put the top part … thank me later
I love the tank but I just can’t get the wicking right. Sometimes my cotton will last me 4 or 5 days. Other times I’m getting dry hits after only a few hours. Just maddening.
Greetings from Croatia. Greetings mike so i have a small problem i am currently using ammit dual and i got my 510 pin during the cleaning and now i lost 510pin so i can not measure the dimensions of the pina maybe you know what its the size of this page I found on the net other than the pin that matches me so if you could help me thank you. https://www.fasttech.com/search?Replacement%20510%20Contact%20ammir%20dual
This tank has an over the top flavour tbh, but the liquid consumption is just retarded anyone else have this xD ?
I brought this after bulid coile cotton etc saying chk your atomaizer !!!
What king of wick for coil did you used? I do not know what to buy
Hello. I had severe leaks with mine. With fresh wick be sure the cotton is not touching the airflow holes because it is going do drip. Put some juice on it because it is easier to shape it then use your pinchers to lift it away. Do not leave the juice holes open when you fill the tank. The pressure created in the tank when you screw the cap is going to push the ejuice and owerflow the deck. With fresh wick after the tank is filled and the cap is screwed open the juice flow fo 1 or 2 seconds then close it. Take 2-3 puffs then open it again and you should see air bubbles. Close it again and take another few puffs. The goal is to gradualy release the presure created in the tank when screwing the cap. Do this also when refilling. For me works. I have filled my pockets with juice many times until i realized its dripping because the cotton was touching the side airflow holes. I hope this will work for you too. I am from Romania so not a native english speaker but hopefully you will understand what i mean. Have a nice vape
Great video Mike- just got 2 shipped over (1 silver, 1 black) did a build on the black with dual coil set-up as directed and it's vaping so sweet straight off the bat. Just came over from the Smok Cloudbeast V8 where I have been rebuilding on their supplied deck. The pillars used to pull inwards and then the seal between the 2 connecters would melt and that was end of deck! Got recommended to buy the Ammit Dual RTA and basically couldn't be happier. Thanks for walking me through the build- spot on directions:)
I’ve had mine about two months and it’s leaking a lot around the air flow collar on the bottom. Ive got juice rings every 30 minuets or so.
bought one back in September and the included a top fill adapter and a piece to separate the air flow down in the base more like the kylin to smooth out the whistling sound just remember if you use the top fill adapter you need to add an oring or it will leak
Can i use single coil without the adapter?
Mine was leaking above the air flow adjustment, put one of the bigger clear o-rings around the build deck just above the treads to mount the tank, no more leaks just made a small gap between the tank and the base!! I like that gap more then the greasy fingers :p
Solution to the leak problem
1st step: Unscrew the pin underneath and remove everything including the air hole, theres also a lil brown cap that remove that to,
Step2: once you have dissembled step 1, reassemble it and tighten the pin as hard as you can of course you will no when to stop cause you will feel like you have tighting that bitch.
This is the reason why it leaks from the airhole an from underneath your tank when you remove it from your mod. You will see leaks.
Now that is solved least but final.
Step 3: put an o ring on both caps. The filling cap and the top closing cap. So therefore both top caps requires an o ring.
Now fucking wick that shit just dont cover the air holes.
An do your self a favour use a single coil is much better.
Enjoy your unleak ammit dual coil tank
Thank me if i have solved your problems
i just don’t understand why everybody is ignoring the metal piece with the two openings.. this piece is found in the lower layer of the packaging and it is meant to keep the glass in its place and not to pop up when opining the top part of the rta … put this part above the glass screw it and then put the top part … thank me later
AdmRiRiiLopLopEz
Thanks Mike for nice review
What is the best coil saving liquid
In this rta and good in flavor?
I can't unscrew the top off mine for the life of me… seems welded shut. Looks effortless when you do it in this video however.
Hey Mike. What scissors are younusing and where can i get a pair?
I love the tank but I just can’t get the wicking right. Sometimes my cotton will last me 4 or 5 days. Other times I’m getting dry hits after only a few hours. Just maddening.
Greetings from Croatia.
Greetings mike so i have a small problem i am currently using ammit dual and i got my 510 pin during the cleaning and now i lost 510pin so i can not measure the dimensions of the pina maybe you know what its the size of this page I found on the net other than the pin that matches me so if you could help me thank you. https://www.fasttech.com/search?Replacement%20510%20Contact%20ammir%20dual
that fill method is awful , i just bought mine and immediately disappointed as i opened the box and disassembled it
I use the 6ML AMMIT DUEL tank and I got a extra piece that holds the glass of the tank so the glass is tight… I love the AMMIT DEUL !!!
What is name of them coils and size you using
My Ammit jui leak…! How fix ???
Please help me…which one is better?ammit dual or manta
This reminds me of the Kylin RTA.
its leaking. whatever i did.
This or the zeus dual rta?