been having a problem how to use temp coeficency rate. cant find any helpful guides in the internet.i built 12 wraps 28g nickel single coil reading .14ohms i cant find the right setup in it. any help please? mike?
I've noticed a really good way to have an evenly spaced ni200 coil is to wrap the coil like normal, without spaces, then – go in between the final wrap on each side and pull it apart so there's a gap between each wrap of the coil. Lastly, push it all together and hold for a few seconds. It should then be evenly spaced as best as it can be. It's like a spring, once it gets uncoiled, it can never go back to fully coiled without there being spaces.
That's also strange it was .1 … I just did a 28g Ni200 3mm build, aiming for .2 – steam-engine.org states 14 wraps (14.3) … you'd think it'd be 10 wraps since it's twice the resistance of yours.
micro coil pro is a great app for building's. nickel, stainless steel, titanium up to 20/wraps spaces or micro, and even twisted. up to 6 coils and up to 6 wires in a coil. Google play store 1 dollar fee
Thanks Mike. Really helped me. I just purchased a DNA 200 device and a Smok TFV4 tank with both RBA Single and Duel Coil heads so I can rebuild my own NI200 coils and try out temperature control. Thanks Again 🙂
Amazing as usual mike just got a tfv4 now I know how to do a tc build in it you definitely got to do one for the kangertech rba double thumbs up man? ?
Question….. I made the same build for my swoop mod with a sx350j chip. I am new to temperature control and was wondering what should I set the temperature in F• and joules at? Thank you in advance
Just a heads up peeps, doing my 3rd build on this deck and noticed the threads are damaged in deck. Have been building for a while so confident it's nothing i have done. Just annoying now the unit is redundant?
hi Mike …I need some help from you please, I vape kanthel and I never tried temp control before, I have only UD ni200 26 awg wire wich I want to use but with help of alot of calculators I end up with 300 or 400 coil raps , my spot targets is 0.5 to 1 ohm …and I wanted to use it on Derringer rda ..(dual coils) is it possible? I appreciate your opinion.
there is a app for android it's called vaporcalc it's amazing, check it out. #hitthatshit
Nice recoil. But how many watt u fire sir?
Great vid! Thanks
So I just installed the included coil in the RT1 and wicked like you shown but it's reading .78ohm is that normal?
been having a problem how to use temp coeficency rate. cant find any helpful guides in the internet.i built 12 wraps 28g nickel single coil reading .14ohms i cant find the right setup in it. any help please? mike?
I've noticed a really good way to have an evenly spaced ni200 coil is to wrap the coil like normal, without spaces, then – go in between the final wrap on each side and pull it apart so there's a gap between each wrap of the coil. Lastly, push it all together and hold for a few seconds. It should then be evenly spaced as best as it can be. It's like a spring, once it gets uncoiled, it can never go back to fully coiled without there being spaces.
That's also strange it was .1 … I just did a 28g Ni200 3mm build, aiming for .2 – steam-engine.org states 14 wraps (14.3) … you'd think it'd be 10 wraps since it's twice the resistance of yours.
micro coil pro is a great app for building's. nickel, stainless steel, titanium up to 20/wraps spaces or micro, and even twisted. up to 6 coils and up to 6 wires in a coil. Google play store 1 dollar fee
Thanks Mike. Really helped me. I just purchased a DNA 200 device and a Smok TFV4 tank with both RBA Single and Duel Coil heads so I can rebuild my own NI200 coils and try out temperature control. Thanks Again 🙂
Mike is the "Bob Ross" of Vaper tutorials.
any reason you don't use the milled holes under the screws? your not using them… don't know if thats on purpose or not.
Hey i'm not sure if this was asked somewhere on here but not from what I see.. Where did you get the stand that your rba base screws into?
when are you going to do the build on the dual RBA base?
Thanks Mike, you're always very real and up front
Thanks mate, excellent tutorial
Where or what site did u order your nickel wire spool?
hi mike i have a 26g nikel will that be good in a five wrap on tfv4 singel coil rba? thanks in advance newbie here
Amazing as usual mike just got a tfv4 now I know how to do a tc build in it you definitely got to do one for the kangertech rba double thumbs up man? ?
Question….. I made the same build for my swoop mod with a sx350j chip. I am new to temperature control and was wondering what should I set the temperature in F• and joules at? Thank you in advance
Hits like champ thanx
Just a heads up peeps, doing my 3rd build on this deck and noticed the threads are damaged in deck. Have been building for a while so confident it's nothing i have done. Just annoying now the unit is redundant?
What's the difference between annealed and tempered Ni200. I'd like to know if it would build the same or the different techniques of each Ni200 wire?
Thanks for the video! Inspired me to do a ni200 build on my tfv4 mini and I can't be happier!
Great video, but can you use nickel wire on a mod with temp control even if you're using wattage on it?
hi Mike …I need some help from you please, I vape kanthel and I never tried temp control before, I have only UD ni200 26 awg wire wich I want to use but with help of alot of calculators I end up with 300 or 400 coil raps , my spot targets is 0.5 to 1 ohm …and I wanted to use it on Derringer rda ..(dual coils) is it possible? I appreciate your opinion.